www.vishay.com 14 PMM0204 vishay draloric document number 20006 revision 12-oct-00 for technical questions contact : ff1aresistors@vishay.com features stable metal film on high quality ceramic very low tc and tight tolerances excellent stability at different environmental conditions force fitted steel caps, tin plated on nickel barrier metal film, cylindrical resistors ? coating: green ? without tc-band ? marking : see appropriate catalog or web page 2) rated voltage: pxr 3) based on measurements on test board acc. to en 140000 packaging: see smm0204 parameter unit PMM0204 rated dissipation at 70 c w 0.125 limiting element voltage 2) v 100 insulation voltage (1 min) v dc/ac peak 200 thermal resistance 3) k/w 220 insulation resistance ? 10 10 category temperature range c - 10 / + 100 failure rate 10 ? /h < 1 weight / 1000pcs g 18 model power rating limiting element temperature tolerance resistance e-series p 70 c 1) voltage max 2) coefficient range wv ppm/k % ? PMM0204 0.125 100 5 0.1, 0.25 100r - 100k 96 - 192 PMM0204 0.125 100 10 0.1, 0.25 100r ?221k 96 ?192 PMM0204 0.125 100 15 0.1, 0.25 100r ?221k 96 ?192 PMM0204 0.125 100 25 0.1, 0.25 100r ?221k 96 ?192 PMM0204 0.125 100 50 0.1, 0.25 100r ?221k 96 ?192 PMM0204 25 562r .1% b1 model tc resistance value tolerance packaging ppm / k ? % b1-blistertape 1000 pcs standard electrical specifications ordering information technical specifications 1) power rating depends on the maximum temperature at the solder point, the component placement density and the substrate material 2) rated voltage: pxr ?tc 10ppm/ c: temperature range is - 10 c to + 85 c
www.vishay.com 15 PMM0204 vishay draloric document number 20006 revision 12-oct-00 for technical questions contact : ff1aresistors@vishay.com metal film, cylindrical resistors ? cecc40000 / 40400 / 40401-803 ? en140400 / iec 60115 ?1 test conditions of test test results endurance test at 70 c 1000 hours at 70 c, 1.5 hours "on", 0.5 hours "off" 0.1 % iec 60115-1 4.25.1 endurance at uct 1000 hours at 125 c without load 0.1 % iec 60115-1 4.25.3 overload test short time overload for 2 seconds 0.02 % iec 60115-1 4.13 2.5 x rated voltage or 2 x limiting element voltage thermal shock rapid change between upper and lower category temperature 0.02 % iec 60115-1 4.19 iec 60068-2-14 damp heat steady state 56 days at 40 c and 93% relative humidity 0.2 % iec 60115-1 4.24 iec 60068-2-3 resistance to soldering heat 10 seconds at 260 c solder bath temperature 0.05 % iec 60115-1 4.18 iec 60068-2-20 performance applicable specifications model dimensions [in millimeters] d max d * l a max a min PMM0204 1.4 d -0.15 3.6 - 0.15 0.85 0.5 * d measured in the middle of the resistor solder pad dimensions [in millimeters] model reflow soldering wave soldering ab l a b l PMM0204 1.0 1.6 2.2 1.2 1.6 2.2 dimensions 1k 5k 10k 50k 100k 500k 1m resistance value in ? current noise 0.01 current noise in v/v 0.03 0.05 0.1 0.3 0.5 1 2 3 -55 -25 0 25 50 75 100 ambient temperature in c current noise 0 rated power in % 20 40 60 80 100 120 70
|
